Restoration timeslabs truck repair

Añadido: 2026-05-27

[00:00:34]Wow.

[00:02:01]The water cleared away the rust. It's deep. We need a crane to lift this. The frame's weak.

[00:02:05]>> Oh, get a heavy wreck now.

[00:02:07]>> Roger that. Sending coordinates.

[00:02:10]The chassis is compromised. The ladder joints are seized.

[00:02:14]This needs heavy equipment. We can't move it as is.

[00:02:17]>> Keep it slow. Watch the tree on the left. Confirm. Reversing slightly.

[00:02:22]Straighten out now. Good.

[00:02:25]Keep coming back. You got it.

[00:02:41]Cable tension is good. Hook is clear to descend. Grab the chain slowly. Coming down easy. Good. Grab. Secure it. Front secure. Rear secure.

[00:02:53]Looks good. Good.

[00:02:55]Take up the slack.

[00:03:04]Clear. Clear. Keep it steady. Looking good. Affirmative. Stabilizing now.

[00:03:13]slow left.

[00:03:17]Pull. Good.

[00:03:21]Contact.

[00:03:28]>> Looking good. Tight.

[00:03:31]Check.

[00:03:34]It's out.

[00:03:57]You're good. Keep coming. Easy does it.

[00:04:00]Stop here. All right. It's home.

[00:04:07]All right, we're set.

[00:04:08]>> That's the spot.

[00:04:09]>> Let's get started.

[00:04:15]>> All right, let's get that angle on the windshield corrosion.

[00:04:17]>> Yeah, >> copy that. Moving to log the rust on the rear panel.

[00:04:47]Measure that thickness there. It's all right. It's right on the edge. Mark it.

[00:04:53]Done.

[00:05:11]Taking the weight. Good balance.

[00:05:15]Watch the hoses. Clear to lift. Moving up.

[00:05:35]Keep it steady.

[00:05:37]Harder hits this time. Got it. One more.

[00:05:40]Watch the balance. Ease it down.

[00:05:59]Keep it steady.

[00:06:01]Harder hits this time. Got it. One more.

[00:06:04]Watch the balance. Ease it down.

[00:06:39]Hook on the lifting eye. Safety clip engaged. Adjusting for balance.

[00:06:45]Testing tension.

[00:07:09]Whoa.

[00:07:13]Heat.

[00:07:35]Heat.

[00:07:39]Heat.

[00:07:59]HEAT.

[00:08:04]HEAT. HEAT.

[00:08:59]17.860 verified. One tap.

[00:10:31]Main power cable secured. Ground strap is good. Insert the 20 amp fuse here.

[00:10:36]Continuity test complete. All systems check out.

[00:11:11]Torque it to spec. 15.5 lbs. Got it.

[00:11:15]Pads inserted correctly. Bleeder access checked. Ready to move on.

[00:12:15]Heat. Heat.

[00:13:11]Line it up good. Just like that. Pass me the wrench. Torque set 25. Checking the slide. Clear of the dash. Looks good.

[00:13:18]Line up the splines.

[00:13:20]Got the wire. Nice. Give it some torque.

[00:13:23]Done. Feels good. Let's test it. Keep it steady. Down a few inches. Stop. Hold it right there. Bolts in. Check the level.

[00:13:32]Looks good. Release the tension. All right. Circuit A is secured. Check the routing on B.

[00:13:39]Routing looks good. Fill the reservoir.

[00:13:42]Engage extension. Pressure holding steady. Reach full extension. Check limit switches. Limit switches confirmed. No leaks. All right. Seated now for the stem.

[00:13:52]>> Looks good. Here's the hose.

[00:13:54]>> Checking pressure. It's two spec. Let's stage it.

[00:13:58]Line it up right there. Got it. Torque pattern.

[00:14:04]Done. All >> good.

[00:14:06]>> Okay. Slowly checking the bell housing alignment. Just a little to the left.

[00:14:12]Perfect. Looking good. Drop it. Torquing down the front mounts now. Uh >> alignment looks good on this side.

[00:14:18]>> Verified. Moving to the final spec.

[00:15:04]She's running. Look at those. Yeah.

[00:15:08]Perfect. Years of work right there.